Pink and Black Valentine’s Wreath Tutorial

A Bold, Elegant Valentine Wreath Using the Ruffle Method

If you love Valentine décor that’s a little less frilly and a lot more bold, this pink and black Valentine’s wreath is the perfect project. The combination of pink, black, and pops of red creates a modern Valentine look that works beautifully on a front door or as a statement piece indoors. In this tutorial, I’ll walk you through the full process using the ruffle method, from cutting your mesh and ribbons to adding a layered bow and securely attaching your sign.

This wreath is built for fullness, height, and durability, and it’s beginner-friendly as long as you follow each step. Let’s get started.

Supplies Needed

• Valentine-themed deco mesh (cut into 30-inch pieces)
• Wired ribbon (various patterns in pink, black, red, and black & white)
• Wreath frame with ties (work form)
• Rotary cutter and cutting mat
• Ribbon cutting tool or scissors
• Pipe cleaners
• Zip tie
• Metal hole punch
• 26-gauge floral wire
• Plastic weaving needle
• Valentine sign
• Bow maker (optional but helpful)

Step 1: Cut the Deco Mesh

Begin by rolling out your deco mesh onto your cutting mat. Using a rotary cutter, cut the mesh into 30-inch pieces. For this wreath, you’ll need nine mesh pieces per ring, so be sure to cut enough for both the bottom and top sections.

Once all your mesh is cut, set it aside and move on to your ribbon tails.

Step 2: Prepare the Ribbon Tails

Take all of your ribbon choices and cut them into 12-inch tails. To save time, you can stack two ribbons together and cut them at the same time.

After cutting, fold each ribbon in half and dovetail the ends by cutting toward the wired edge. This keeps your ribbon tails neat and polished. You’ll be making nine sets of ribbon tails per ring.

Step 3: Create the Bottom Ring Ruffles

To make things easier, gently pull the inner ring of the frame inward so it doesn’t interfere while you work on the bottom ring.

Take one mesh piece, tuck the edge under slightly (about ¼ inch), and scrunch it straight up the center using your thumbs and fingers. This creates a shape similar to a bow tie.

Place the scrunched mesh into the tie, secure it tightly, and then spread the mesh outward on both sides. Pull the mesh slightly upward along the edge of the frame to give it extra height and volume.

Repeat this process around the entire bottom ring, working two mesh pieces at a time if possible. This reduces fraying and helps maintain a clean look.

Step 4: Add Ribbon Tails to the Bottom Ring

Once your mesh ruffles are secured, fold each ribbon tail set in half, pinch at the center, and place it into the same tie as the mesh. Tie it tightly, trim off excess tie length, and push the ends to the back.

Fluff the ribbons by gently curling them upward and alternating ribbon patterns around the wreath for balance.

Step 5: Build the Top Ring

Open the ties on the top ring and repeat the same ruffle method used on the bottom ring. Be careful not to squash the mesh below as you work.

For the ribbons on the top ring, you’ll crisscross them instead of placing them straight. Position the larger ribbon pieces across the wider openings and angle the smaller ribbons slightly to the side. This adds depth and visual movement.

If any ribbons want to droop, gently push them backward to create a small indentation. Wired ribbon makes this step much easier and helps everything stand up nicely.

Step 6: Make the Valentine Bow

Start your bow with black ribbon as the base layer.

• Create an 8-inch tail
• Make four loops at 6 inches each

Next, add a 1.5-inch ribbon in black, pink, and red:

• Six-inch loops
• Slightly longer tails for dimension

For the pink and black-and-white ribbons, make slightly smaller loops at 5 inches. This allows the bottom ribbon to remain visible.

Secure the bow with a zip tie, then add a pipe cleaner in the groove of the bow maker. Twist and pull each loop gently to “break” the bow and create fullness. Fluff the loops and tails until you’re happy with the shape.

Attach the bow directly to the wreath frame using the pipe cleaner and trim any excess.

Step 7: Attach the Sign Securely

Punch a hole on each side of your sign using a metal hole punch. Cut about 20 inches of 26-gauge wire and thread it through the holes, twisting the ends together.

On one side, run the wire directly to the frame and secure it tightly. On the other side, use a plastic weaving needle to guide the wire through the mesh and down to the frame. This saves time and keeps the wire hidden.

Twist the wire around the frame, trim the excess, and tuck everything neatly into the back.

Final Touches

Give the wreath a gentle shake, adjust the mesh and ribbons, and re-fluff the bow if needed. Once everything is secure and balanced, your pink and black Valentine’s wreath is complete.

This design is full, eye-catching, and perfect for Valentine’s Day décor with a modern edge.